You could just use it to trigger any single given smartthings – controlled device that shows up in the IFTTT SmartThings channel. So the next question is what do you want to do for the “that” in your IFTTT applet? You are definitely going to use the SmartThings channel, but how are you going to use it? So once you get this far, you have an event which recognizes when the IBeacon either goes in range or out of range. So when the I beacon comes in range of your phone/tablet, the message gets sent to IFTTT, and that becomes the “if” in your IFTTT applet But you still need the other two pieces, a receiver device ( typically a smartphone) and a receiving station app running on that phone. So as far as your question about whether that particular transmitter device will “work” it depends on what you are using for your receiver device and your receiving station app. That allows you to use the IFTTT maker channel as the “if” in an IFTTT applet and to use the smartthings IFTTT channel as the “that” in the same applet. You then set it up to send that webhook to the IFTTT maker channel. One way to integrate an Ibeacon with SmartThings is to use a receiving station app that can send a webhook (http post) based on the specific transmitter ID that it receives. There are also some third-party receiving station apps that you can buy, although these are less common than they were two years ago because now many people write their own apps. Some have a full “SDK” ( software development kit) which is a set of programming tools for people who want to write their own receiving station app. Most of the companies that make the transmitting Devices have their own apps that can do this. Three) you need some kind of app that can recognize that the receiver device has received a transmission and then make a decision based on the ID of the message. But it’s just the receiver, on its own, it doesn’t do anything just because it received a message from the IBeacon. It has an active Bluetooth radio that will receive the transmission from the IBeacon. Two) there is a receiver device, typically a phone or tablet. Whether that’s going to be of any use to you will depend on the other two parts that you are using. The device that you linked to is an IBeacon, so it is going to transmit. That’s why it is often compared to a lighthouse – – the lighthouse sends out its light whether there are ships in the area or not. All it does is transmit a tiny message over and over giving its device ID. One) there is a transmitter device, the IBeacon. There are three parts to any system based on I beacons. RadBeacon X4 - All-weather, Long-life Bluetooth Smart Proximity Multi-beacon Using iBeacon and AltBeacon Technology But that requires at least three Ibeacons for each region, and just gets quite expensive for home automation. But I single I pbeacon just can’t identify a person walking into A room, because its detection zone is not stopped by the walls.Įstimote has an excellent microlocation system which is generally sold to stores and Sporting arenas, so that you could, for example, send someone one coupon if they are in the men’s department and a different coupon if they are in the shoes department next to it. They make good touchless switches if you set the range very small, like around foot. The kitchen and a living room right next to it will be seen as the same- and so will the bedroom one floor up. There’s no concept of a “room” as a human defines it. That’s because they are based on Bluetooth, which goes right through the walls (and the floor and the ceiling). So a single Ibeacon is very good as an identifier for when a phone or tablet comes within a 360 degree range of that beacon.īut they aren’t going to work for Microlocation based on rooms or interiors very well unless you spend a lot more money and get a much more complex app. ![]() It’s quite easy to integrate them with SmartThings if you use a receiving station app which can generate an HTTP post ( webhook) as then you can use the IFTTT maker channel as the “if” and smartthings as the “that”. I have used them in my house for about two years, as I have discussed in the forums. Assuming you mean Ibeacons, I would say they work very well for the purpose for which they are designed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |